日本少妇xxx,亚洲免费综合色图,julia一区二区三区中文字,色图图av

<label id="u77v3"><del id="u77v3"></del></label>

    <span id="u77v3"></span>

  1. <label id="u77v3"></label>
    <rt id="u77v3"><optgroup id="u77v3"><strike id="u77v3"></strike></optgroup></rt>
    <form id="u77v3"><strong id="u77v3"><blockquote id="u77v3"></blockquote></strong></form>
    <li id="u77v3"></li>
    <span id="u77v3"></span>
      <i id="u77v3"></i>
      <span id="u77v3"><optgroup id="u77v3"></optgroup></span>

      Hello, Welcome to FCTEL Technology Co.,Ltd
      National service hotline:+086 0571-87007055/56/57 CN

      WE ONLY FOCUS ON TRANSMISSION AND ACCESS

      Products center

      framed E1-FE Converter

      Type:FCC-E1fF1523 Message

      Description:1channel framed E1 - FE converter ,N * 64k rate setting ,With E1 loopback detection function

      Product Description
                    This interface converter is based on FPGAproviding one framed E1 interface and one Ethernet interface to achieve 10/100base-T Ethernet data transmission on the E1 channel. It is a high performance self-learning Ethernet bridge. This device is the extension device of Ethernet using network (PDH/SDH/Microwave) that provide E1 channel to achieve local and remote Ethernet interconnecting with serial interfaces at a lower cost. The device has inter-set loop test function to facilitate the project launching and daily maintenance.

      Functional Properties
      ◆   based on self -copyright  IC 
      ◆   Can realize monitor and control of remote equipment OAM management data did not  take up user’s timeslot and save E1 bandwidth
      ◆   E1 supports any timeslot set the rate is 64K-2048K
      ◆   The local device can forced the remote device rate follow it
      Ø    Have the function of E1 interface loop back check avoid the converter crashed because of interface loop return;
      Ø Have indicator  when the device is power-off or E1 line is broken or lose signal;
      Ø Can set the E1 line that not to send the LINK signal to Ethernet interface while E1 line is broken;
      Ø The Ethernet interface supports jumbo frames (2036 Bytes);
      Ø Inter-set dynamic Ethernet MAC address (4096) with local data frame filtering 

      Ø Ethernet interface supports10M/100M half/full duplex auto- Negotination and AUTO-MDIX

            (crossed line and straightly connected line self-adaptable );

      Ø Have Ethernet monitor self-reset function the equipment will not dead
      Ø Can achieve the remote device setting any 5 mode of Ethernet and can closed the AUTO-MDIX function; 
      Ø Provide 2 clock types: E1 master clock and E1 line clock;

      Ø Have three Loop Back Mode: E1 interface Loop Back (ANA)、Ethernet interface Loop Back(DIG)、Command the remote

            Ethernet interface Loop Back(REM) 

      Ø Provide 2 impedances: 75 Ohm unbalance and 120 Ohm balance;
      Ø Support SNMP Network Management;
      Ø Can realize monitor of remote equipment temperature and voltage from local equipment;  
      Ø Can form the structure: Ethernet E1 Bridge(A)---E1 Optical Fiber Modem(B)---Ethernet Optical Fiber Modem (C) 

      Ø   Can form the structure: Ethernet E1 Bridge(A)---Optical Ethernet Modem(B)---Ethernet Optical Fiber Transceiver (C) 

            can manage (B) and (C) at (A)


      Technical Parameters

      ◆   E1 Interface

          Interface Standard:      comply with protocol G.703;
          Interface Rate:             n*64Kbps±50ppm;
          Interface Code:            HDB3;

          E1 Impedance:             75Ω (unbalance) 120Ω (balance);

          Jitter tolerance:            In accord with protocol G.742 and G.823

          Allowed Attenuation:   0~6dBm

      u Ethernet interface (10/100M)

          Interface rate:              10/100 Mbps half/full duplex auto-negotiation

          Interface Standard:      Compatible with IEEE 802.3 IEEE 802.1Q (VLAN)

          MAC Address Capability: 4096

          Connector:                  RJ45 support Auto-MDIX

      u   Power

          Power supply: AC180V ~ 260V;DC –48V;DC +24V

          Power consumption: ≤10W

      u   Dimension          

       

          Product Size :       216X140X31mm( WX DXH))

          Simple packaging : 274X193 X84mm ( WX DXH)

          Piece Weight: 1.1KG

      u  Working environment

          Working temperature: -10°C ~ 50°C
          Working Humidity:        5%~95 % (no condensation)

          Storage temperature:   -40°C ~ 80°C
          Storage Humidity:         5%~95 % (no condensation)

       

      Application Scheme

      Applications 1

      Applications 2

      Applications 3

       

      DataSheet Download
      ?